Glass pipes can be very dirty especially if it has been used for a long time and have not been regularly cleaned. Doing the cleaning is actually simple. Learn how to do it through these basic ways.
Remove any particles which should not have been there by simply turning it upside down and tap it gently. Then flush the inside portion with running water so that any dirt that has attached will also be removed. Use caution in holding the wet object because it might slip in your hands and be dropped.
The usual method of cleaning and which is also the most tested on is through using rubbing alcohol. Get a resealable bag or the usually sandwich bag and have it be filled with alcohol enough for filling the bottom part. The solution should be sufficient in amount so that the object could be entirely submerged when it is placed in the bag.
Place the bag and the thing in the microwave but be sure that is properly covered with the solution and then set the timer to ten seconds. Wait until the alcohol will boil and be cautious because this would happen so rapidly. Avoid heating it for a very long time to prevent melting of the plastic and breaking of the glass.
Take the bag out of the microwave and shaking of the entire thing will allow the alcohol to go inside the tubing and this will result to the taking of the debris away. The thing itself will remain in the plastic because it should still be soaked overnight so that the hardened dirt will be loosened. Seal it properly and keep it there for about eight to ten hours.
After soaking, the thing can be taken out and rinse it well with cold water which is preferably running. Sometimes there will still be additional deposits which have not yet loosened especially if it has not been cleaned for a long time. Get a pipe cleaner or even a simple cotton swab can do the work in taking off the remaining stubborn dirt and rinse with water.
Have the object be thoroughly dried before it can be used and this is the final part of the process. If the use of alcohol is not preferred, another option that can be possible is by using boiling water. Fill a small pot with water that is enough to submerge the object and then boil it on a gas or electric stove.
After it has been brought to boil, the heat should be reduced to cause only simmering and by that time the object can be placed safely but make sure that it would be entirely submerged. Ascertain that you already have removed any particles inside. Simmering will be good for only twenty up to thirty minutes then rinsing follows.
Do not put the glass pipes in water that is boiling if these objects are cold because they might shatter but you should be warming them with your hands first. Using the boiling method will cause a strong smell to diffuse inside the house and be prepared for it. Wash each object thoroughly before use.
Remove any particles which should not have been there by simply turning it upside down and tap it gently. Then flush the inside portion with running water so that any dirt that has attached will also be removed. Use caution in holding the wet object because it might slip in your hands and be dropped.
The usual method of cleaning and which is also the most tested on is through using rubbing alcohol. Get a resealable bag or the usually sandwich bag and have it be filled with alcohol enough for filling the bottom part. The solution should be sufficient in amount so that the object could be entirely submerged when it is placed in the bag.
Place the bag and the thing in the microwave but be sure that is properly covered with the solution and then set the timer to ten seconds. Wait until the alcohol will boil and be cautious because this would happen so rapidly. Avoid heating it for a very long time to prevent melting of the plastic and breaking of the glass.
Take the bag out of the microwave and shaking of the entire thing will allow the alcohol to go inside the tubing and this will result to the taking of the debris away. The thing itself will remain in the plastic because it should still be soaked overnight so that the hardened dirt will be loosened. Seal it properly and keep it there for about eight to ten hours.
After soaking, the thing can be taken out and rinse it well with cold water which is preferably running. Sometimes there will still be additional deposits which have not yet loosened especially if it has not been cleaned for a long time. Get a pipe cleaner or even a simple cotton swab can do the work in taking off the remaining stubborn dirt and rinse with water.
Have the object be thoroughly dried before it can be used and this is the final part of the process. If the use of alcohol is not preferred, another option that can be possible is by using boiling water. Fill a small pot with water that is enough to submerge the object and then boil it on a gas or electric stove.
After it has been brought to boil, the heat should be reduced to cause only simmering and by that time the object can be placed safely but make sure that it would be entirely submerged. Ascertain that you already have removed any particles inside. Simmering will be good for only twenty up to thirty minutes then rinsing follows.
Do not put the glass pipes in water that is boiling if these objects are cold because they might shatter but you should be warming them with your hands first. Using the boiling method will cause a strong smell to diffuse inside the house and be prepared for it. Wash each object thoroughly before use.
About the Author:
You can visit the website www.spoonyswholesaleglasspipes.com for more helpful information about Secrets In Cleaning Glass Pipes
0 comments:
Post a Comment